What Causes Water Leaks?

Home » What Causes Water Leaks?

What Causes Water Leaks?

By | 2017-11-28T05:54:20+00:00 May 6th, 2017|Categories: resource|

The Truth Behind Water Leaks

One of the very problems in plumbing systems is leaks which is very difficult to find out. Knowing that all of the plumbing systems are place under the ground, you cannot determine whether your plumbing system has damage unless it shows any sign. One common leak in the plumbing system is the pinhole leaks. By the name itself, pinhole leaks only drops couple of water at a time. The early you spot pinhole leaks the better, or better call Emergency Plumbers Chicago for a full inspection of plumbing system. Do not under estimate the pinhole leaks because it can cause inconveniences if not taken care off. Find out more about it below.

First seen on (http://www.thetrustedplumber.com/blog/plumbing-service/how-to-protect-against-pinhole-leaks/)

Leaks are a very common problem for plumbing systems across the country. One of the problems with combating leaks in a plumbing system is how difficult it is to detect them in the first place. Most of the average plumbing system is hidden from view, and leaks tend to be quite small. In fact, one of the most dangerous types of leaks is the pinhole leak, which is only large enough to leak a couple of drops of water at a time. Let’s take a closer look at pinhole leaks, and how you can detect them early.

What are Pinhole Leaks?

A pinhole leak is the breakthrough (puncture) of the copper pipe due to the progressive attack of the pitting corrosion process. A copper water plumbing system can experience significant damage from pitting corrosion but not result in pinhole leaks for many years.

Pinhole leaks are most common in copper pipes. They are created by chlorine particles in the air or soil quickly degrading the copper in the pipe, a process called pitted corrosion. Pitted corrosion can open leaks in the pipes quite quickly, and though they never grow that large they can still pose a serious threat.

The Problem of Pinhole Leaks

It is precisely because they are small that pinhole leaks cause so much damage. Even only leaking a couple of drops at a time a pinhole leak can inflict widespread water damage. Most homeowners don’t notice pinhole leaks until they see the area around it has been rotted out. By then, it’s far too late to mitigate the majority of the damage.

The best way to detect these problems early is to have your plumbing inspected at least once a year. That way, your plumber can find and patch any pinhole leaks long before they have time to damage the plumbing system too heavily. You can save thousands of dollars in repair costs over the years by doing this.


Now that we have determine the causes of pinhole leaks in your water system. How can you repair it and how plumbers can fix the problem. Here is a better overview on how to get your leaks repairs. Read more

First seen on (http://www.doityourself.com/stry/how-to-repair-a-pinhole-leak-in-a-copper-pipe#b)

Cooper pipes are often plagued by pinhole leaks. The cause of these leaks is hotly debated in plumbing circles; however, how to fix them is not. Though you could use some type of chemical sealant, the easiest way for do-it-yourselfers to repair a pinhole leak in a copper pipe is to use a repair clamp. Repair clamps are available in a wide variety of materials and sizes. They can be found at most every home improvement center or hardware store. In order to complete this repair, you will the repair clamp and a rag. This repair should take no more than 20 minutes to complete and will save you a call to the plumber and quite a bit of cash.

how-to-repair-pinhole-leakStep 1—Measure the Damaged Pipe

Repair clamps come in various sizes. To properly repair the pinhole leak you will need to know the size of the pipe. You can then buy a repair clamp that will fit the pipe perfectly. Note the measurement and take it with you to the home improvement store when you buy the clamp.

Step 2—Turn Off the Water

Before you begin working, you will need to turn the water off. It is best to turn the water off to the entire house when you begin working with the pipes.

Step 3—Clean the Pipe

In order to place the repair clamp, you should clean the pipe. The pipe doesn’t need to sparkle but it should be free from dust and any type of buildup. Use a dry rag to wipe the area where you will be placing the clamp.

Step 4—Place the Repair Clamp

The repair clamp will have a flexible metal pad on the inside. The pinhole should be centered on the rubber pad. You will open the clamp and place it in the desired area. You close the clamp and use the screws to tighten it. You want to make sure that the clamp is tight, that is how the leak will be stopped. However, you must take care not to over tighten the clamp because this could actually damage the pipe. Over tightening the clamp can cause so much damage to the pipe that it breaks or a larger leak develops. Therefore, it is best to tighten the clamp and then move on to Step 5.

Step 5—Turn the Water Back On

Once you believe the clamp is tight enough, you should turn the water back on. With the water back on, you will be able to ascertain whether or not you need to tighten the clamp more. If the leak has ceased, you know you have properly installed the clamp. If there is water still leaking from the pinhole, you will need to tighten the clamp additionally.


That being said, you can save money in repair cost if pinhole leaks will be fixed early. Aside from it, another problem that cause water leaks is the loosen faucet or simply call it faucet leaks. This can be detected easily because unlike the pipes that are hidden underground (where pinhole leaks happen) faucet is being use in a day to day basis. Read further below to know more about water leaks.

First seen on (https://myplumber.com/2016/03/15/one-leaky-faucet-wastes-5-gallons-day-1800-gallons-year/)

How much water does a leaky faucet actually waste?

The average household’s leaks can account for more than 10,000 gallons of water wasted every year, or the amount of water needed to wash 270 loads of laundry. It all starts with a little drip, and it really doesn’t seem like that big of a deal. One drop of water every few seconds — what could that be doing, really? More thank you think. Break it down this way. Imagine one drop, every few seconds, 24 hours a day, seven days a week. It adds up. Imagine if this was every faucet in your home, in your neighbor’s home, in all the homes that surround yours.

The math can only be approximated because every drop of water from every faucet is a slightly different size, and falls at a slightly different rate, but using the US Geological Survey’s average of 1/4 millimeter per drop, it would take about 15,000 drops to equal one gallon of water. And sure, 15 thousand drops sounds like a lot, but a faucet that drips a drop every second would fill that gallon in just four and a half hours.

That’s five gallons a day, 35 gallons a week, and as many as 1800 gallons a year. Suddenly, that little drip doesn’t seem like such a small amount of water anymore.


Remember to call an expert plumber if you have water leaks problem in your home. The early the leaks are fixed the better because it can save you from you paying huge amount on your monthly bill. Call Emergency Plumbers Chicago today! Their certified plumbers works promptly and efficiently, they are committed to provide an effective solution in regards to different plumbing system issues.